The tapered barrel on these bushings is split on both sides, allowing them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for work with with split-tapered sprockets and pulleys of the same bushing design. As you tighten the included screws, the bushing grips the shaft and pulls it in to the sprocket or pulley.
This Split Taper Bushing is designed exclusively for use with cast iron bushed bore pulleys and will be purchased on a single page as the pulley you will need. For employ with 5/8” shaft sizes. Includes set screws. More Features: Made of Steel For apply with cast iron bushed bore pulley
Our stock steel Split Taper bushings feature wrench torque capability from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are utilized on sheaves, pulleys, sprockets and gear belt pulleys. The split tapered bushing alleviates the need to have a component bored to size, ideally lowering on hand requirements and enabling adjustments in shaft size if necessary. The barrel of the split tapered bushing is usually split in two locations and is definitely keyed to the shaft. The barrel OD is also keyed to the travel component as well. The good thing about the split tapered bushing could it be will hold, whether or not the fasteners become loose. Split tapered bushings happen to be interchangeable between manufacturers.

Taper bushing are widely used as well as sprockets, v-belt pulleys, timing pulleys, coupling and other mechanical parts with taper bore connections.
Taper bushing series are constructed of high Split Taper Bushing china quality engineered products with great tolerance. The feature is easy to make use of and needs no more alteration. These bushings can suit almost all sorts of assemblies and sizes. They will be the best choice in design for mechanical connections.
To complete designations add bore size. For instance: PD1215X16MM designates a 1215 taper bushing with a 16mm bore.
No costly re-boring: complete selection of both metric and imperial offered.
Standard range matches up to 125mm/5″ shafts & Hub diameter required is determined by the application.
Complete brief reach range obtainable, for compact light and portable assemblies & Clean, Compact Design.
Ease of installation and removal.
This Split Taper Bushing is designed exclusively for use with cast iron bushed bore pulleys and may be purchased on a single page as the pulley you will need.
For use with 1 3/16” shaft sizes.
Includes 2 set screws.

Additional Features:
Made of Steel
For use with cast iron bushed bore pulley
This U1 Bushing with 5-1/2″ bore is a high-quality precision product that is built for toughness and strength. U1 bushings are used in an extensively wide selection of applications, which includes; sprockets, shaves, pulleys, gears, and much more, we likewise offer most of these products. What models this bushing apart is the high-quality steel development along with precise manufacturing and top quality control; this means that you always get yourself a premium quality consistent product. What really models us in addition to the other folks is our experienced expert staff members and our company-wide objective of customer satisfaction.
1. Be sure the tapered cone areas of the bushing and the inside of the driven merchandise are clean and free of anti-seize lubricants.
2. Place the bushing in sprocket or different part type that accepts the bushing.
3. Place cap screws loosely in pull-up holes. The bushing remains loose to assure sliding match on shaft.
4. With crucial on shaft, slide the sprocket or other part type to the required position on the shaft. Make sure you keep the heads of the cap screws accessible.
5. Align the sprocket or part type, tighten the screws additionally and progressively until they are pulled up tight. Do not work with extensions on the wrench handles and don’t allow the sprocket or component to always be drawn i connection with flange of bushing. At this time there must be a gap between your bushing flange and sprocket, make sure this gap will not close.
Dual split barrel ensures concentricity
Grips the shaft with confident clamp fit
High torque carrying capacity
Permits blind assembly
Load not carried or limited by mounting screws
External key of all sizes for positive drive and higher torque carrying capabilities
Double-split barrel for positive clamping
Solid flange to keep concentric bores
Available in in ., metric, and spline bores. Bore range between 3/8″ to 10″
Solid Flange & Dual Split Barrel – Assures better concentricity to the shaft.
Key to Key Travel – With keys in both shaft and merchandise to provide the strongest possible travel.
3/4″ per Foot Taper on Barrel – Personal locking taper supplies the highest amount of mechanical locking item to product.
The tapered barrel on these bushings is split on both sides, allowing them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for apply with split-tapered sprockets and pulleys of the same bushing design. As you tighten the included screws, the bushing grips the shaft and pulls it in to the sprocket or pulley.
This Split Taper Bushing was created exclusively for use with cast iron bushed bore pulleys and will be purchased on the same page as the pulley you will need. For employ with 5/8” shaft sizes. Comes with set screws. Added Features: Made of Steel For employ with cast iron bushed bore pulley
Our stock steel Split Taper bushings feature wrench torque capability from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are used on sheaves, pulleys, sprockets and equipment belt pulleys. The split tapered bushing alleviates the need to have a component bored to size, preferably lowering on hand requirements and enabling adjustments in shaft size if important. The barrel of the split tapered bushing is definitely split in two spots and is normally keyed to the shaft. The barrel OD can be keyed to the drive component aswell. The benefit of the split tapered bushing is it will hold, whether or not the fasteners turn into loose. Split tapered bushings will be interchangeable between manufacturers.